Day 3 of making the ladder (by alaric)

Well, after two days of prior work on the ladder, yesterday I settled down to another day.

I started by welding together the second side of the ladder, to match the first. With that done, I now had the two sides of the ladder, ready to join them together with the rungs:

With that done, I carefully aligned everything on the welding bench and ground the welds on the inward sides down so that the rungs could fit on nicely:

I set the rungs back half a centimetre where they were attached at the same point as a spacer, so they were welded both to the uprights and to the spacers, as I felt this would be stronger. The pieces of wood you can see under the rungs are maintaining that spacing.

Now, as I mentioned before, I'm not very good at welding; I can make things structurally sound, but not pretty, because my welds often go wrong and I have to go over them again. This usually leads to big, messy, welds, and on a couple of occasions with this job, I actually melted a hole in the metal and had to patch it up. Here's one particularly terrible weld:

I ground the lumps around the edge of the hole down:

Then welded a metal plate over it:

This, in contrast, is I think the neatest weld I've ever made:

With all that done, the ladder was actually a ladder:

I sanded it down to get the weld gunk off, then washed it thoroughly in white spirit to remove the grease the metal came covered in, and laid it out in the kitchen to paint:

Then I gave it a priming coat and left it to dry overnight (I did it in the kitchen so it would be warm and dry overnight, rather than the cold and damp of the workshop):

It'll need another couple of coats of paint, and I need to cap the open ends of the uprights at the top, then I can mount it on the wall.

Part of welding that I always find quite profound is the way that a bunch of bits of metal, initially held together with clamps, and gingerly handled in case it comes undone, slowly transforms into a structure made of solid steel. This was driven home with the ladder project when, finishing the welds on the rungs, I found the best way was to lay it on its back like in the last photos and sit on it so the welds were flat (the best orientation, as molten metal likes to run away when the weld is vertical) and comfortable to reach; it didn't even flex!

I can't wait to be using it to get up on the roof. There's a flap of plastic sheeting lifting up in the wind and letting rain in, and I can't reach it in any other way...

Continue to day 4...

Poets Work (by sarah)

Saturday I went into Cheltenham to meet friends and write and what have you. It was great to see my friend Andy again who I orginally met at a writing group in Cheltenham back before the floods!

The postcards and stickers of my art work arrived for moo so I gave him some one of each which he seemed really happy about 🙂 He also told me I should be selling them.

Somehow three hours disappeared in the blink of an eye.

Then I went on to Centre Arts who are running an Arts Cafe on Saturday afternoons. I managed to fall off my chair - a prelude to passing out and stuff later in the day which was unfortunate but I recovered and they were very helpful and understanding as always!

I felt stupid but a cup of coffee and several poems inspired by the artwork later, I was having a fine chat with an artist/nurse who was in there drawing away.

I also managed to talk to my friend who runs the place about the Science-Art Exhibition we will be running in March which is very exciting and lots of organising needs to be done!

Alaric was concerned about me so bought me a four pack of irish stout which did seem to really help - he then made me lots of green veg for dinner and we discussed the bleeding problem :/

I've also had a neck spasm for the last week or so which is making typing and drawing and reading hard but I am steadily working my way through it. On the plus side the continual headache I've had for the past year seems to have disappeared with the coil 🙂

I finished the day off by sorted out my poetry mug - I love this cupcake tea cupe 🙂

It may not sound like work but with the aememia acting up it was very exhausting for me but it was definately worth it. I'd been in on Tuesday as well to watch a talk about The European History of Warewolves which was interesting by (Deborah Hyde)[http://www.jourdemayne.com/about-jourdemayne].

It was a narrowed down talk so covered a later bit of history than what I have been researching lately. However it did tie in with the time period of the first Punk storyline and I'd very much want to add in the warewolf, witch and vampire myths on top but within the context of actual history, science and the storyline itself. Well that was really the point of going!

From a writing point of view Tuesday was a very productive day - I spent it trying to get an overview of Europe from the fall of the Roman Empire to the Tudor period but completely side tracked myself in disease history (as you do!).

This was all whilst cuddling Mary who was in one of her slightly grumpy I am teething moods so wouldn't be put down.

After the warewolf talk, I wrote a horror story based on real accounts of the Black Death - I should have been sleeping but had brain over load!

I freaked myself out slightly and ended up having to wake Alaric up - this is a good sign though - I feel my best horror stuff is written in this way - though poor Al was not amused!

I have a story idea that came out of the talk too but it is very disturbing so can't face writing it yet. It maybe shelved until GothNoWriMo or something.

The talk was good in another way though - I realised as I miss people who think and know stuff. I was sitting there and some makes a comment about us and chimpanzees and I know it's wrong and before I can say anything someone else corrects the guy! It just sort of felt like uni again and I have always really missed that atmosphere.

Writing wise this month is being hectic with me running WoPoWriMo too and I really want to donate some more poems to charity cause - one for the disabled and their fight at the moment and some for Freedom - a book shop that was fire bombed in London on Friday.

So I am chugging along with the work thing - never as fast as I want but little bits will build-up.

One Leg Longer than the Other (by sarah)

So awhile ago Alaric started having horrible lower back pain which we thought was initially a slipped disc as did the Dr and he got refered to physio and he seemed sorted but then it came back, this time with exploding knee and things. It has been getting worse and more frequent though disappears in the intermediate stages - he had to be tested for various other nasty things like bone cancer etc... especially as he was having the night sweats and things but these were all clear.

Further prodding and pocking reveals he has a wonky pelvis leading to inflamation of the thorasic joint - he has siattica basically. He is fixable - especially as it appears the wonk has been caused in the first place by one leg being short than the other. He says in hind sight there has always been an issue with him getting into trouble for 'tripping people up' as he naturally stands with the longer leg sticking out.

So he needs manipulation and special shoes, but the nhs wont fix him, they will prescribe pain killers and send him to pain management but wont fix him as it will cost too much. His Dr has given him the contact details for the person she went too as she had the same problem.

I just don't understand the logic of the nhs - left untreated he will end up a cripple and dependent costing them alot of money. I suppose it's why save money for a tomorrow we shall not see :/

But more than that - when I was at school we had a medical in secondary school where they measured everything and checked spins were straight and all sorts - he apparently didn't have this - I can't help but think the leg issue would have been picked up then - the amount of damage all ready done which could have been solved by made to measure shoes with different height soles :/

So the mission is to sort him out - we can't afford for both of us to be cripples. When his back is bad we have to work together in the most ludicrous of ways to get the most simple things done. Not too bad at the moment as I am walking again but there were a few dicey weeks when I was on crutches and he couldn't lift anything last year. We had to work in tandum to get the baby seat in the car etc...

Poetry Madness! WoPoWriMo 2013 (by sarah)

It is the first of February and that means only one thing! That's right another one of my mad writing challenges!

This time it is poetry.

The objective is to write a poem a day for the whole of Feb. It is called WoPoWriMo and I am also looking after the website and stuff this year for it.

As with NaNoWriMo I have roped in my family - so far I have Alaric, Mum, Dad and Jean doing it.

I have had emails from several poets already who do not wish to sign up but are going to be using the exercises to help them get going with writing again which is fantastic!

I myself plan to take part in the challenge also! Which I will be writing about on Turquoise Monster, I will find out were Al is posting his. Many people are posting there's to linkedIn and to the WoPoWriMo site itself under the poems tab.

There will be blog alteration later today to put up web-badges and what not! In the mean time I'd best get on with actually doing some writing!

Sealing up the workshop’s eaves (by alaric)

I keep moaning about how the workshop roof leaks, causing rain to drop down on all my nice tools and supplies. But that's not the only problem with the workshop roof!

The workshop is basically a set of walls, with the roof resting on top. The roof is a large, flat, box with the bottom open (exposing the rafters that give it strength), slightly larger than the outline of the walls. The rafters rest on the tops of the walls, and the roof hangs slightly over the walls.

As you may have guessed if you've been following that, this means there's gaps all the way around the edge of the roof. Howling winds blow through them. These holes are enormous at the ends of the building, where the roof overhangs further; twenty centimetres high and occupying most of the length of the walls (interrupted only by the rafters themselves), but I've pinned up sheets of plastic to temporarily block them until I get around to cutting lots of rectangles of wood to properly cover them with.

Along the longer walls of the building, the gap is more like a centimetre, but again more or less the entire length of the building (which is somewhere around ten metres).

And the worst part is, the rear wall is close to a row of trees, which are covered in ivy. And the ivy has found the gaps and keeps oozing its way into the roof.

And as well as being faintly disturbing, the ivy also drops foul grime down onto my stuff.

So, although stopping the roof leaking is a long-term project I work on when I get entire days to spend building the ladder to get up there, I've been fighting the ivy when I've just had a few hours here and there. I've been cutting bits of thin wood (left-over cladding) and nailing them in place over the larger holes, and then liberally applying left-over bits of sealant to all the edges (I suspect the ivy attacks a gap if it sees light, so hopefully this will make it lose interest). The black marks on the ceiling are damage made by ivy I've torn out:

There's no less than three different colours of sealant there - two different cartridges of brown "frame sealant", one light and one dark, and some leftover bits of white stuff from the bathroom! Unbelievably, it looks miles neater than the mess of cobwebby, grimy, ivy that was there!

I have to climb right up into the eaves to get most of the gaps, however. This picture is not particularly clear, but there's a thin plank of wood that I've nailed down to the top of the wall in order to cover the two-centimetre gap between the top of the wall and the vertical wooden beam at the back, then I've run sealant all around all the gaps and joints:

I quite like working with sealant (I've been sealing gaps in the bathroom, and replacing existing manky mouldy sealant - and doing it neatly, unlike the ghetto job I'm doing in the workshop), and it's nice to think that I'm keeping out all those draughts and grubby plants! I want to properly seal all the gaps in the workshop - and then introduce an extractor fan over the welding bench at one end, and an air inlet vent at ground level at the other end, with a small heater under computer control so I can regulate the temperature and keep the humidity down in here!

I've also started varnishing a bit of scrap MDF that, I have realised, is exactly the right size to make a shelf to go over my workbench (not the welding bench, the one where I have the column drill). That will give me a place to put loads of things that currently sit ON my workbench for lack of a shelf. Also, I'll be able to fit a decent light to the bottom of the shelf; right now, when I work at the workbench, I cast a huge shadow over whatever I'm doing.